By: Klaas van Ditzhuyzen
Units are expressed in metric and prices in US dollars, unless otherwise stated.
An optical pyrometer is a device which allows contactless temperature measuring by using the incandescense color. It is based upon the fact that all black bodies do have the same incandescense color at a given temperature. It is very straightforward and allows any temperature from which a hot object emits light ( > 500 deg C). It is made from a small magnifying optical device (like a monocular or very small telescope) in which a small incandescent bulb is placed which image is sharp when the user views through the eyepiece (the lens(es) on the eye end of the optical device). The background is the hot object to be gauged. The electrical current flowing through the filaments in the bulb is an indication of their temperature. This current is controlled by a potentiometer which is put between the power source (a battery) and the bulb. An ammeter is used to display the temperature. Its range is from 500 C (== 900F lower limit when an object incandesces) to 1600 C (3000 F), which is suitable for most applications.
The stuff needed is available in a local hardware or electronics shop unless stated otherwise.
- Small optical device. A 5×20 (5 = magnification, 20 is objective (front lens) diameter in millimeters) is OK. It should be able to focus till less than 30 cm (1 foot). Available at a second hand optics dump store for a few dollars. An old, unrepairable half of binoculars can also be used (like I did).
- Battery or batteries to make 5 or 6 Volts. Four nickel-cadmium, nickel metal hydride or alkaline penlites in a four batteries holder are suitable.
- A resistor of 47 Ohms 1/4 Watt when you use 1600 C range to protect the ammeter from overflow. When alkaline batteries are used (4×1.5 = 6V) instead of nickel (-cadmium) ones (4×1.25 = 5V), take a 56 Ohms one.
- A small incandesent bulb, not larger than 7 mm in diameter, otherwise it blocks the background image of the hot object. It should not draw more current than 100 milliamperes. Take a 6 Volts one. I have a 6 Volt / 100 mA one. An ordinary bicycle light bulb is usually too large in size.
- Potentiometer of about 470 Ohms linear and a round knob easy to handle.
- Low-power power switch.
- Low-current wires.
- Two 30mm or 1 1/4″ hose clamps.
- An empty 35mm film canister preferably Kodak, because it’s sturdier and black (I don’t have Eastman Kodak shares). Not the empty metal roll which is sent with the roll to the photo lab, but the plastic cylinder in which the roll is sold.
- Plastic box of about 100x60x50mm (4″ x 2 1/2″ x 2″), which is available in electronics shops and mounts to attach it to the optical device.
- Analog voltmeter with 2 Volts range. A low range ammeter (e.g. 10 mA) serial with a 200 Ohms precision resistor (1 % tolerance) can also be used. When full 2400 C (4400 F) range is used, take a 500 Ohms precision resistor and omit the first 47 or 56 Ohms resistor. In this case, only one-third of the scale is used for the first 1600 degrees, so this is recommended when you use very high temperatures often.
- When using high temperatures (over 1300 C), a welding filter glass.
This all should not cost more than $40 all together. The binocular can be obtained at a photo repair shop where they probably have an abandoned half of a pair of binoculars.
- A simple multimeter which allows measuring DC milliamps, ohms and volts. Available from about $30 in the local electronics shop, or you might borrow it from a friend.
- Soldering iron and solder.
- Screwdrivers, sharp knife and piercing device (or a small drill).
- Torch which is able to reach temps you need to be measure and some pure metals (nickel, copper, gold, aluminum) to calibrate. A thermocouple with a proper display can also be used.
- Take off the eyepiece of the binoculars and put the film box between the eyepiece and the prism box. This is necessary to make the light path longer to allow viewing close objects (as your furnace is) sharp. Try out what the best length is. Maybe you must cut off a part of the film box. Attaching the eyepiece to the film box can be done best by a 30mm hose clamp.
- Pierce a hole in it to put the light bulb on the front side of the eyepiece, in such a way that you see it sharp from the eye end of the eyepiece.
- Connect the bulb in the following way:
- Plus of the battery to power switch
- Power switch to 47 Ohms resistor then to the left contact of the potmeter.
- Center contact of the potmeter to bulb and the ammeter + 200 Ohms precision resistor and bulb in parallel and that back to battery ground. The whole stuff should be built in the plastic box with the potmeter knob, power switch and the ammeter on the front. Check for the polarity of the ammeter. Attach the box to the binocular, such that the wires to the bulb in the eyepiece are properly fitted and the controls (power switch and potmeter knob) are easily to reach while viewing through the eyepiece.
Here is the electric scheme:
6 V 60 mA bulb R=47 Ohms ------(X)------------------ \ | | + |--XXX---- X\X | | - \--------- O ------- XXX --------| ___ | - | | ----------------------------------------------- 5..6 V 470 Ohms 10 mA 200 Ohms 1% battery potmeter ammeter resistor
When it is all assembled, then the heat goes on….
The readout takes place the following way: Point the pyrometer to the object to be measured, preferably a nonlustrous object (blank metal surface) and not at flames, because the latter are gases or scattered soot particles. The glowing filaments in the bulb in the pyrometer should be in the image of the object. Turn the potmeter so far till you hardly see the top (hottest part) of the bulb filaments. Then the temperature of the filaments is correct and you should read the current on the ammeter Determine which calibration temperatures you are going to use. If you have a thermocouple and a furnace with a stable temperature and the display of the thermocouple is correct, just adjust the furnace to a few round numbers (e.g. 600 C, 1000 C or 1000 F , 1800 F, etc.) and read the current for these values when you point the pyrometer at the thermcouple and the filaments of the bulb glow the same color.
When you don’t have a thermocouple, melting (or freezing) metals is another option. The best are:
pure platimum 1773 C / 3222 F pure nickel 1453 C / 2647 F pure copper (use a reducing flame !) 1083 C / 1981 F pure aluminum (calibrate with low light) 660 C / 1220 F
Point the pyrometer on a thin oxide layer, as the lustrous metal reflects too much and does not show exactly the proper color. Repeat each calibration once or twice to be sure about the correct temperature.
Write down all currents matching the temperatures and make an interpolation to make a new scale. Do this on a piece of paper with the same size at the ammeter scale.
When putting the scale on the ammeter, remove carefully the plastic cover of the ammeter and (don’t touch the needle hand!) paste it carefully over the ampere scale.
Now your pyrometer is ready for use. When batteries get low, it will not affect the accuracy, because the display is just the voltage over the bulb and low batteries will just limit the range. When using high temperatures (over 1300 C) placing a welding filter between the light bulb and the eyepiece or in front of the front lens (objective) is a strong recommendation to protect your eyes. But not between the object and the light bulb, because then you filter the hot object, but not the light bulb.
Alternate sources for manufactured pyrometer equipment:
1.) The Pyrometer Instrument Company, Inc.
2.) Spectrodyne, Inc. Providers of the latest in disappearing filament Optical Pyrometers and Calibration Services.